The glossary is in English only.
Product Categories
Alphabetical order
A-C
- acceleration rate
- acceleration thrust force
- automatic indexing function
- back electromotive force constant (=back EMF constant)
- backlash
- backlash correction function
- bifilar winding
- bipolar drive
- break communication
- break function
- category 5, 6
- center
- center device
- circular interpolation
- clockwise
- closed-loop control
- cogging force
- command position counter
- command pulse
- common pulse mode
- communication code
- communication cycle
- communication method
- communication protocol
- communication speed
- comparator
- constant speed operation
- continuous linear interpolation
- continuous operation
- continuous rating
- coreless forcer (= moving coil)
- counter-clockwise
- CPU emulation communication
- CPU emulation device
- current position counter
- cyclic communication
- cyclic communication cycle
- cyclic redundancy check
D-H
- damping control / vibration suppression control
- data communication
- data communication time
- data device
- deceleration rate
- detent torque
- deviation counter
- deviation counter clear signal
- device attribute information
- device information
- device number
- digital hall sensor
- effective stroke
- EL signal (=End limit signal)
- encoder
- end point lead-in function
- excitation sequence
- feedback scale
- FH correction function
- field bus
- frame
- general-purpose port
- half-duplex communication
- high speed operation (=FH operation)
- holding torque
- hub device
- hybrid-type stepping motor
- hysteresis positional error
I-M
- I/O communication
- idling pulse
- impedance
- induction noise
- in-position signal (IMP signal )
- input change interrupt
- input/output device
- insulation resistance
- intermittent rating
- interpolation control axis
- limit escape operation
- limit positioning operation
- linear interpolation operation
- linear acceleration/deceleration
- linear encoder
- linearstep
- linking
- local
- local device
- manual pulser
- maximum slewing pulse rate (frequency)
- maximum starting pulse rate (frequency)
- mechanical external input signal
- mechanical position counter
- message communication mode
- micro-steping drive
- monofilar winding
- Motionnet system
- multi-drop connection
N-P
- next operation automatic start control
- NRZ (=Non Return to Zero) code
- number of rotation
- open-loop control
- operating (=ambient) temperature range
- operating (=ambient) voltage range
- ORG (=Origin) signal
- origin escape operation
- origin return operation (=homing)
- origin return operation with feeding amount limit
- origin search operation
- out-of-step
- output-pulse mode
- output-pulse width control
- parallel bus
- PCL device
- permanent magnet type stepping motor
- polling
- port
- position override
- positional accuracy
- positioning control
- positioning operation using pulser inputs
- pre-register
- preset counter
- preset operation
- pull-in torque
- pull-out torque
- pulse rate
- pulse transformer
R-S
- rated current
- rated current (=constant current)
- rated current drive
- rated thrust force
- rated voltage (=constant voltage)
- rated voltage drive
- reference clock
- resolution
- resonance (phenomenon)
- responsiveness
- re-try
- ring counter
- rotor inertia
- RS-485 standard
- S-curve acceleration/deceleration (control)
- S-curve section
- SD (Slow-down) signal
- servo motor I/F (=interface)
- settling time
- shaft motor
- signal reflection
- single phase excitation
- single step rise time
- slewing area
- slip correction
- slow-down
- slow-down point (=ramping-down point )
- slow-down point auto setting (=ramping-down point auto setting)
- slow-up
- slow-up/ slow-down (ramp-up/ ramp-down)
- software limit function
- speed control
- speed fluctuation rate
- speed setting step number
- speed step value
- speed unevenness
- starting torque
- start-stop region
- step angle
- system communication
T-Z
- temperature rise
- termination resistor
- the number of interpolation steps
- the number of positioning pulses
- the number of residual pulse(=remaining pulse)
- thrust constant
- thrust control
- timer operation
- T-NET system
- torque characteristics
- transient communication
- transient transmission
- transmission speed
- triangle drive avoidance (=elimination) function
- triangle(=triangular) drive
- unipolar drive
- variable reluctance type stepping motor
- vernier drive
- vibration restriction function
- watch-dog timer
- winding inductance
- winding resistance
- zero position return operation